iriskin Posted March 3, 2012 Share Posted March 3, 2012 (edited) Hi, this problem has been bugging me for quite some time and nothing i tried had been able to fix it. I use RecordingService and DVBViewer on same machine. Sometimes, when i start DVBViewer it starts normally, but sometimes it hangs on "Completing Initialization" stage and after about 10-15 seconds DVBViewer loads, but says that there is no hardware device available and goes to standby mode But after i click the channel manually - everything starts working. I have no idea what is the cause. It happens only around 25-30% of the time. Other times when i launch DVBViewer everything works fine from the start. Without Recording Service i haven't seen a single case of this behavior. I included support.zip. Here's some additional info: Gigabyte EX58-UD4 Intel I7-920 @3.6Ghz NVIDIA GTX285 6gb RAM @1400Mhz 8-8-8-24 Prof-7500USB DVB-S2 Win7 64 bit english. Latest drivers for everything. I can reupload screenshots to imgur.com later, if you need. It says it's over capacity now. Edited March 3, 2012 by iriskin Link to comment
Lars_MQ Posted March 3, 2012 Share Posted March 3, 2012 03.03.12 04:02:07.678 TUniCastServer Could not listen: Address not available (#10049 in Bind) It seems the network is not ready. Don't know what happens on your machine/system... Link to comment
iriskin Posted March 3, 2012 Author Share Posted March 3, 2012 (edited) I've reset all network settings in windows and gave it some test. This problem still appears sometimes, but instead of mentioned above error in svcdebug.log, another error in osderror.log appears: 03.03.12 14:02:17.233 TWSocketThread Could not connect: Zugriffsverletzung bei Adresse 004A90E3 in Modul 'DVBViewer.exe'. Schreiben von Adresse 00586EB0 Any idea what it could be? Edited March 3, 2012 by iriskin Link to comment
krasno Posted March 4, 2012 Share Posted March 4, 2012 Hi, this problem has been bugging me for quite some time and nothing i tried had been able to fix it. I use RecordingService and DVBViewer on same machine. Sometimes, when i start DVBViewer it starts normally, but sometimes it hangs on "Completing Initialization" stage and after about 10-15 seconds DVBViewer loads, but says that there is no hardware device available and goes to standby mode But after i click the channel manually - everything starts working. I have no idea what is the cause. It happens only around 25-30% of the time. Other times when i launch DVBViewer everything works fine from the start. Without Recording Service i haven't seen a single case of this behavior. Exactly same problem here! I have found out that in most cases it helps to stop DVBV, then stop recordingservice, wait 10 seconds, start it again, wait 10 seconds and then start DVBViewer. If not: restart of PC hepls The "standby" + no hardware issue started in December 2011 I think. I have an idea it is browser related, but I have also experienced that unplugging CI and plug it in again, + dvbv. restart sometimes helps. The slow initialisation started here long time ago, I think in end of 2010, I did post a question about about start up time once...as far as I remember, but can't find the post.. Link to comment
KlokanSoft Posted February 19, 2016 Share Posted February 19, 2016 Also the same problem, (DVBViewer_5.5.2)YUAN MC763M change hw / MC763H Hybrid Analog / DVB-T miniPCI, Asus notebook N75SF. Start DVBT HW found. DVT-Tuner red-flagged. Remove it, rescan DVT HW-Tuner loaded, then it works normally again.DVBT shuts down and the device is lost again :-(Not somewhere to define the device to write to INI? Link to comment
Recommended Posts